What is a Burette? Types & Uses

What is a burette?

If you are a chemical scientist or happen to know one, it’s likely that you have heard the term ‘burette’ being used. If you have ever wondered, what is a burette and what is a burette used for, let’s help you solve this mystery.

For one who has ever performed a quantitative analysis in a chemistry lab, you would most likely have come across a burette. The word ‘burette’ has French origins and was coined by the chemist, Joseph Louis Gay-Lussac.

A burette is a laboratory apparatus, which consists of a long, graduated glass tube, with a stopcock on its lower end. It is used in quantitative chemical analysis to measure the volume of a liquid or gas. It is used to dispense and measure a variable amount of a chemical solution. The stopcock valve controls the flow of the fluid from the burette, either in a steady stream or drops by drop.

A burette (sometimes also spelt as buret) is often used in the process of titration. Titration is a process of chemical analysis in which the quantity of some constituent of a sample is determined by adding to the measured sample an exactly known quantity of another substance with which the desired constituent reacts in a precise proportion.


Types of burettes

Burettes can be classified in different ways:

  1. As per the mechanism

  • Volumetric burette – The volume scale is printed on the burette wall
  • Piston burette – Syringe design with barrel and plunger arrangement
  1. As per operation

  • Manual burette – Marked by graduations and operated manually
  • Digital burette – Operated manually or electronically with digital displays
  • Electronic burette – Motor-controlled operations with the elimination of human errors, and electronic display
  1. As per fluid handled

  • Liquid burette – Dispenses liquids. The stopcock is at the bottom of the burette, and the flow of the fluid is enabled by gravity
  • Gas burette – Dispenses gases. The stopcock is at the top of the burette, and the gas is collected by displacing a liquid like water or mercury, through a fluid reservoir at the bottom

Uses of Burettes

Now that we have some information about burettes, let’s find out what is a burette used for.

As we saw before, burettes are used in the process of chemical titration. These can include acid/base titrations, reduction/oxidation titrations, and precipitation titrations. 

A burette can hence be used in the below industries:

Pharmaceutical Industry: Verification of concentrations in medicines

Food Industry: Testing the acidity levels of food liquids

Cosmetic Industry: Verifying concentration of ingredients in a safe amount

Meteorology: Measuring the amount of gases in the air

Bio-fuel Manufacturing: Measurement of impurities in bio-fuel

Medical Diagnosis: Analysis of body fluids like urine and blood



How to use a burette; General tips and tricks for titration

Now that we know more about the uses of the burette, we give you step-by-step pointers and best practices to use a burette for titration:

  1. Rinsing: Rinse the burette with the liquid you wish to use. Do this by adding a small amount of liquid into the buret, turning the pipette horizontally and rotating it so that the liquid contacts the entire inside surface of the burette. Let the liquid drain through the stopcock into a waste container.
  2. Support: Place the burette in appropriate support. This can be done by using a burette clamp attached to a ring stand.
  3. Filling: Fill the burette with the titrating solution to be used just above the zero mark (+/- 10mm). Fill the tip of the burette with the solution. If necessary, the funnel can be placed on the upper end of the nozzle to help fill.
  4. Remove air bubbles: The burette should not have air bubbles in the tube after the liquid is filled. If there are bubbles, use rubber or other items that will not break the glass to tap the wall to allow the bubbles to float out of the surface. There may also be air in the channel of the stopcock switch. In this case, the plug should be twisted several times quickly, and the bubble can be discharged.
  5. Initial Reading: Verify that the burette is sealing well. To make a reading of the liquid level in the burette, the reading must be made tangentially to the lower part of the meniscus. Keep your eyes to this level, to avoid parallax errors
  6. Dripping: Open the stopcock and slowly allow the liquid to drain into the receiving vessel until it approaches the end point.
  7. End Point: You may add the titration solution quickly until a few milliliters less than the endpoint. After that, one should be careful when adding the solution, to determine the endpoint accurately. When the appropriate amount of liquid has been delivered close the stopcock and touch the buret to the side of the vessel to remove any partial drops.
  8. Final Reading: Read the volume of the remaining liquid.
  9. Calculation: The volume of liquid delivered can now be calculated by subtracting the Final Reading from the Initial Reading.
  10. Drain: Drain the buret of any excess liquid and rinse it with water to clean it.

Summary

We have seen the different types of burettes and their usage, and also the step-by-step procedure of use. It may seem overwhelming at the beginning for unpracticed hands, but as with anything, practice makes perfect. When operating a burette, use chemicals with caution, and adopt proper disposal methods after tests are complete. For extra precision, digital and electronic burettes can prove to be the best bet.

 

Also Read: Everything You Need To Know About Back Titration

Related aticles

lab coats
27
Sep

Lab coats safeguard the safety and hygiene in any laboratory setting, and as a lab manager, the choice between disposable and reusable coats can greatly impact both your operational budget and the safety of your staff.

Conducting a cost-benefit analysis can determine why reusable ones are better suited for your facility. Read on to explore the pros and cons of sustainable coats, and the cost-benefit analysis for the managers by assessing their safety, environmental impact, and cost.

Lab trays
25
Sep

Any laboratory cannot do without them as they can perform many things from organising to being catch-alls. Lab trays are made to eliminate clutter and abide by this work environment’s systematic rule.

May they be metal, plastic, or glass, these trays also come in many forms and sizes. They can also be moulded into specific shapes or moulds to fit the type of substance they are going to contain. These substances can be liquid, solid, or any material that may be dangerous to hold by hand or dangerous to the skin. 

Let us look into the roles and significance that these essential trays can provide within an experiment room setting.